Log:
Téléchargements : 5   Taille : 336 kb   Fabricant : Henny Penny  
Catégorie : Séchoirs
@name

If a humidity error occurs, and you want to use the cabinet without humidity, turn the humidity off by following the directions for SP-4, Humidity Setpoint, in Special Programming Section of this manual. Once the setpoint is off, the alarm stops, but the error code shows in display. (Includes “E-12A”, “E-12B”, “E-17” and “E-18”). 4-8 804 Model HHC-990 5-2. ERROR CODES AND WARNINGS (Continued) Display Cause Panel Board Correction “E-41 SYSTEM DATALOST” • Memory scrambled • Turn switch to OFF posi

Téléchargements : 7   Taille : 336 kb   Fabricant : Henny Penny  
Catégorie : Séchoirs
@name

Press and “SP-7, OUT OF WATER TRIP POINT” and the preset trip point temperature shows in display. If the float switch fails, the trip point temperature is the water pan temperature at which the control senses the water pan is out of water. We recommend a trip point temperature of 450o F (232o C). 17. Press to change the out-of-water trip point. SP-8 Clean Water Pan Setpoint 18. Press and “SP-8, CLEAN WATER PAN SETPOINT,” and the preset temperature, at which the controls senses that the water pan

Téléchargements : 8   Taille : 336 kb   Fabricant : Henny Penny  
Catégorie : Séchoirs
@name

Add more water to the water pan. 4. Open the doors only as necessary to load and unload product. This helps to keep the interior conditions constant and saves energy. 3-5 303 Model HHC-990 3-5. CLEANING Daily: PROCEDURES 1. Turn all controls off and disconnect electrical supply. To avoid burns, allow the unit to cool before cleaning. 2. Open doors and remove all trays and racks from unit, and take them to a sink to thoroughly clean.Figure 3-3. Figure 3-3 3. Wipe interior and exterior of cabinet

Téléchargements : 8   Taille : 336 kb   Fabricant : Henny Penny  
Catégorie : Séchoirs
@name

PROBE CLIP (OPTIONAL) The probe clip is an accessory, that may be ordered as an option, to hold the food probe when not in use. Remove one of the module screws and mount the probe clip with that screw. See photo at left. The food probe is accessed easier if the clip is mounted on the side of the unit that the door opens. See photo below. Probe Clip Mount clip here. 303 2-5 Model HHC-990 SECTION 3. OPERATION SECTION 3. OPERATION 3-1. INTRODUCTION This section provides explanations of all controls

Téléchargements : 10   Taille : 336 kb   Fabricant : Henny Penny  
Catégorie : Séchoirs
@name

4-3 Section 5. TROUBLESHOOTING 5-1. Troubleshooting Guide ........................................................................................... 5-1 5-2. Error Codes and Warnings.................................................................................... 5-2 GLOSSARY ......................................................................................................................... G-1 Distributors List - Domestic and International i 303 Model HHC-990 SECTION 1. INTRODUCTION SE

Téléchargements : 13   Taille : 336 kb   Fabricant : Henny Penny  
Catégorie : Séchoirs
@name

factory, Eaton, Ohio, or F.O.B. authorized distributor. To validate this warranty, the registration card for the appliance must be mailed to Henny Penny within ten (10) days after installation. REPLACEMENT PARTS: Any appliance replacement part, except lamps and fuses, which proves to be defective in material or workmanship within ninety (90) days from date of original installation will be repaired or replaced without charge F.O.B. factory, Eaton, Ohio, or F.O.B. authorized distributor. The warra





catégories