Évaluations - 2, GPA: 4 ( )

Instructions Delta, Modèle WILLIAMSBURG 2804

Fabricant : Delta
Taille : 463.43 kb
Nom Fichier : bbf8a7e7-3677-4448-9977-6f3bb255c3ea.pdf
Langue d'enseignement: en
Aller à la télécharger

Facilité d'utilisation

Make sure WHITE FOAM GASKET (5) is under flange of DRAIN BODY (4). Fig. B. Note: No plumber’s putty or caulk is required. The CABLE ATTACHMENT POINT (6) must face towards the rear of the SINK. Fig. B. Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). Fig. A. 2 REAR OF SINK 4 5 6 3 1 SINK DRAIN HOLE FLAT SIDE OF GASKET MUST FACE DOWN 1 2 Fig. A. 2 1 FLAT SIDE OF GRAY LOCKNUT MUST FACE UP INSTALL GRAY LOCKNUT 5 Install GRAY LOCKNUT (1) onto DRAIN BODY (2) from below SINK. Fig. A. Note: The flat side of the GRAY LOCKNUT (1) must face up. Tighten firmly by hand. No tools are required. Check DRAIN FLANGE in SINK to ensure that WHITE FOAM GASKET (3) is fully compressed and not visible. Fig. B. POP-UP KNOB (1) must be fully down. POP-UP KNOB Fig. A. Fig. B. 3 WHITE FOAM GASKET NOT VISIBLE DRAIN FLANGE Fig. B. 1 M968422 Rev.1.2 DOWN 2 COMPRESSION NUT 3/8” COMPRESSION CONNECTION COUPLING NUT FLEXIBLE SUPPLIES 3/8 O.D. BULL-NOSE RISERS Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 6 ATTACH CABLE CONNECTOR Fig. A. 2 1 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Fig. B. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 7 CHECK OPERATION OF POP-UP 1-1/4” O.D. Fig. B. 1/2" PIPE THREAD 2 Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. 8 MAKE WATER SUPPLY AND WASTE CONNECTIONS FERRULE 1 2 3 NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE PURCHASED SEPARATELY. HOT COLD M968422 Rev.1.2 1 3 2 1 4 1 9 TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3). Operate both HANDLES (1) to flush water lines thoroughly. Replace AERATOR (3). 5 2 3 CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions. Release POP-UP KNOB (4) down and check all drain connections and "P" trap for leaks. Tighten if necessary. 12 “P” TRAP WASTE OUTLET M968422 Rev.1.2 10 INSTALLATION OF OPTIONAL METAL LEVER HANDLES (Supplied with Faucet) Thread PORCELIAN LEVER HANDLE (2) counter-clockwise and remove INDEX BUTTON with MOUNTING ROD ASSEMBLY (1), HANDLE COLLAR (4) and O-RING (5). Insert MOUNTING ROD ASSEMBLY (1) into METAL HANDLE (3), HANDLE COLLAR (4) and O-RING (5). 3 2 6 1 4 7 Thread HANDLE ASSEMBLY (6) into ball of HANDLE BASE (7). Apply p...

Ce manuel est également adapté pour les modèles :
Plomberie - WILLIAMSBURG 2804 (463.43 kb)
Plomberie - WILLIAMSBURG 2804 (463.43 kb)
Plomberie - WILLIAMSBURG 2804 (463.43 kb)

Écrivez votre propre critique du dispositif

Texte du message
Votre nom :
Entrez les deux chiffres :