Log:

Omnimount UN-A-B

Téléchargements : 0 Taille : 211 kb    Fabricant : Omnimount  
Catégorie : Projecteurs

Omnimount TILT-PA

Téléchargements : 8 Taille : 1017 kb    Fabricant : Omnimount  
Catégorie : Projecteurs

TPUM-1: Tilting Pipe Adapter B. A. To adjust tilt 1. Hold A with 3/ 4” Socket 2. Loosen B with 3/ 4” Socket 3. Loosen C with 9/ 16” Socket 4. Position Display 5. Tighten A,B, & C • Designed for 26” - 55” Flat Panel • Maximum Weight Capacity: 175 • Connects to 1.5” NPT Pipe Specifications are subject to change without prior notice. Every effort has been made to provide accurate and error-free assembly and installation. Omni- Mount Systems disclaims liability for any difficulties arising from the

Omnimount PMD2

Téléchargements : 5 Taille : 353 kb    Fabricant : Omnimount  
Catégorie : Projecteurs

Note: Orient the cable management port on the pipe drop assembly so that it faces the projector cable drop. Extended Ceiling Mount For installations that require a ceiling drop in excess of 18”, standard 1 .” pipe may be used to extend the standard pipe drop assembly. Pipe extension should be cut to the required additional length, threaded on both ends, and then attached to the standard pipe drop assembly with a pipe coupler (not supplied). Note: Orient the cable management port on the pipe drop

Omnimount PMD1

Téléchargements : 1 Taille : 353 kb    Fabricant : Omnimount  
Catégorie : Projecteurs

6 Determine required mounting screw size ( 4, 5 or 6 mm) for projector. Note: Consult projectors owners’ manual for screw sizes and mounting holes. Lay projector on table with mounting surface face up. Place grid section of bottom projector mounting plate onto top of projector in desired mounting orientation (horizontal or vertical). (Fig. 6) Using a pencil or felt tipped pen, mark the locations of the projectors threaded inserts onto the grid for refer- Part Projector Mounting Hardware Qty. Bag

Omnimount PMD.5

Téléchargements : 10 Taille : 353 kb    Fabricant : Omnimount  
Catégorie : Projecteurs

Every effort has been made to provide accurate and error- free assembly and installation. OmniMount Systems disclaims liability for any difficulties arising from the interpretation of information contained in these instructions. If OmniMount products are used for purposes other than their original intent, OmniMount, its distributors and retailers shall not be held responsible or liable for injuries or property damage, direct, indirect, or consequential, which may arise from the inability to use

Omnimount PMD Series

Téléchargements : 13 Taille : 172 kb    Fabricant : Omnimount  
Catégorie : Projecteurs

Omnimount PMC-AL

Téléchargements : 4 Taille : 172 kb    Fabricant : Omnimount  
Catégorie : Projecteurs

Omnimount PFC-A

Téléchargements : 28 Taille : 160 kb    Fabricant : Omnimount  
Catégorie : Projecteurs

PFC-A (Female to Female Coupler) OMNI (Not Included) PFC Coupler 1 r 1 - fl V_!-■ <»-^P-A NPT pipes Available Sizes 12", 18", 24" (Not Included) (Not Included) Pouch # Part # Description Qty 1 COUPLER (PMD Series Compatible) 1 1 P-A SCREW 1/4 inch L 3/8 inch 4 1 P-B ALLEN KEY M4 1

Omnimount OM10131

Téléchargements : 9 Taille : 4 mb    Fabricant : Omnimount  
Catégorie : Projecteurs

Omnimount L27-OM1100149-CON-021810vC

Téléchargements : 2 Taille : 13 mb    Fabricant : Omnimount  
Catégorie : TV

USER MUST REMOVE TELEVISION OR OBJECT OFF THE BRACKET BEFORE ADJUSTING. IF THE PRODUCT IS A TELEVISION MAXIMUM WEIGHT CAPACITY SUPERSEDES / OUTPLACES RECOMMENDED DIAGONAL MEASURED TELEVISION SIZE!! EL USO CON EL PRODUCTOS MAS GRANDE QUE EL PESO MAXIMO Y TAMANO PUEDE CAUSAR INESTABILIDAD Y POSIBLEMENTE HERIDAS. EL USUARIO DEBE QUITAR LA TELEVISI ON U OBJETO DEL SOPORTE ANTES DEL AJUSTE. SI EL PRODUCTO ES UNA TELEVISI ON, LA CAPACIDAD DE PESO MAXIMA REEMPLAZA EL TAMANO DIAGONAL RECOMENDADO DE LA T





catégories